MENUS

You can set the trays and the power-saving function of the printer.

  1. Press or on the operator panel to display [MENUS], and then press (OK).

  2. Press or to display the item you want to set, and then press (OK).

  3. Change the setting, and then press (OK).

    [*] is added to the right side of the set value.

  4. Press (ONLINE) to switch to [READY TO PRINT].

TRAY CONFIG

Item

Factory default setting

Description

MP TRAY CONFIG

PAPERSIZE

A4 or LETTER

Sets the paper in the MP tray.

X DIMENSION*1

210 MILLIMETER or 8.5 INCH

Y DIMENSION*1

297 MILLIMETER or 11.0 INCH

MEDIATYPE

PLAIN

MEDIAWEIGHT

MEDIUM

TRAY USAGE

WHEN MISMATCHING

TRAY1 CONFIG

PAPERSIZE

A4 or LETTER

Sets the paper in Tray 1.

X DIMENSION*1

210 MILLIMETER or 8.5 INCH

Y DIMENSION*1

297 MILLIMETER or 11.0 INCH

MEDIATYPE

PLAIN

MEDIAWEIGHT

MEDIUM

TRAY2 CONFIG

PAPERSIZE

A4 or LETTER

Sets the paper in Tray 2.

X DIMENSION*1

210 MILLIMETER or 8.5 INCH

Y DIMENSION*1

297 MILLIMETER or 11.0 INCH

MEDIATYPE

PLAIN

MEDIAWEIGHT

MEDIUM

PAPER FEED

TRAY1

Specifies the paper feed tray.

AUTO TRAY SWITCH

ON

Sets the auto tray switch function.

TRAY SEQUENCE

DOWN

Sets the selection order for auto tray selection and auto tray switch.

DUPLEX LAST PAGE

SKIP BLANK PAGE

If blank pages are skipped and data on odd-number pages are printed on both sides, the final page is printed on one side.

  1. [X DIMENSION] and [Y DIMENSION] are displayed only if [CUSTOM] is selected for [PAPERSIZE].

SYSTEM ADJUST

Item

Factory default setting

Description

POW SAVE TIME

1 MIN

Sets the time before transitioning to Power Save mode.

SLEEP TIME

1 MIN

Sets the time before transitioning to Sleep mode.

AUTO PW OFF TIME

4 HOURS

Sets the time before transitioning to Auto Power Off.

ECO MODE

ON

If set to [ON]: In the case of making a small number of prints, printing starts even when the fuser has not reached the specified temperature.

If set to [OFF]: Printing starts when the fuser reaches the specified temperature.

CLRABLE WARNING

ONLINE

Sets the timing to remove the display of warnings that can be cleared.

AUTO CONTINUE

OFF

Sets whether to automatically recover the printer when a memory overflow occurs.

MANUAL TIMEOUT

60 SEC

Sets the time in seconds that it takes for the printer to cancel a job in paper feed waiting state when printing with manual feed.

TIMEOUT INJOB

40 SEC

Sets the printer's wait time (seconds) from the stoppage of data processing to the outputting of the pages.

TIMEOUT LOCAL

40 SEC

Sets the time to keep the ports open after a process is complete. (excluding network)

TIMEOUT NET

90 SEC

Sets the time to keep the network port open after a process is complete.

LOW TONER

CONTINUE

Sets the printer action to be taken when toner is low.

JAM RECOVERY

ON

Sets whether to retry the printing of pages that were not printed due to paper jam after the paper jam is cleared.

ERROR REPORT

OFF

Sets whether to print an error report when an internal error occurs.

HEX DUMP

-

Prints data received from the host computer in hex dump. To end printing, turn off the printer.

PRINT ADJUST

Item

Factory default setting

Description

POSITION ADJUST

MP TRAY

X ADJUST

0.00 MILLIMETER

  • X correction: Corrects the position of the whole print image in the direction perpendicular to the paper feed direction.

    Available range: ±2.00 mm (in units of 0.25 mm)

  • Y correction: Corrects the position of the whole print image in the paper feed direction.

    Available range: ±2.00 mm (in units of 0.25 mm)

  • Duplex printing X correction: Corrects the position of the print image in the direction perpendicular to the paper feed direction when printing the back side of the duplex prints.

    Available range: ±2.00 mm (in units of 0.25 mm)

  • Duplex printing Y correction: Corrects the position of the print image in the paper feed direction when printing the back side of the duplex prints.

    Available range: ±2.00 mm (in units of 0.25 mm)

Y ADJUST

0.00 MILLIMETER

DUPLEX X ADJUST

0.00 MILLIMETER

DUPLEX Y ADJUST

0.00 MILLIMETER

TRAY1

X ADJUST

0.00 MILLIMETER

Y ADJUST

0.00 MILLIMETER

DUPLEX X ADJUST

0.00 MILLIMETER

DUPLEX Y ADJUST

0.00 MILLIMETER

TRAY2

X ADJUST

0.00 MILLIMETER

Y ADJUST

0.00 MILLIMETER

DUPLEX X ADJUST

0.00 MILLIMETER

DUPLEX Y ADJUST

0.00 MILLIMETER

PAPER BLACK SET

0

Corrects the variation in print that is caused by temperature difference. Change the value when blurring occurs.

DARKNESS

0

Sets the print density.

SMR SETTING

0

Corrects the variation in print results that is caused by temperature and humidity conditions, as well as differences in print density and the frequency of printing. Change the setting if there is unevenness in the image quality.

BG SETTING

0

Corrects the variation in print results that is caused by temperature and humidity conditions, as well as differences in print density and the frequency of printing. Change the value if the background is dark.

DRUM CLEANING

OFF

Sets whether to perform drum cleaning before printing. This may improve image quality.

HIGH HUM. MODE

OFF

Changes fusion temperature as a measure to prevent paper from curling.

QUIET MODE

OFF

Applies the low-speed printing mode for reducing print noise.